Call Today

They are making a few good annotation on the subject of Installing A Bathtub in general in this post in the next paragraphs.

Installing a tub isn't precisely rocket science, however it does need solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a new one is also a moderately challenging project. If the old bathtub is easily easily accessible, the job can relocate immediately; if you have to open a wall to get rid of the old tub and position the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to leave the old tub as well as embeded in the new one. Ensure you have actually certified yourself for the work and also fit trying it. Instead of working with a specialist to take control of a halfway-completed job, it is better to consider using one prior to you start. Opportunities are you may need an expert plumber to make tube connections.
This post will certainly assist you set up a new bathtub in your restroom if you have currently purchased a new bathtub and also don't need to transform the plan of your previous water supply pipelines.
Your devices as well as material list must comprise the following:

• New Bath tub


• Hammer


• Pipe Wrenches


• Prybar


• Shatterproof glass


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Tape Measure


• Pipeline Caps


 

Preparing for the Installment

Firstly, the sustaining framework provided with the bath must be fitted (if called for) according to the maker's guidelines. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to see to it that if the tap features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is additionally sensible to fit a sustaining plate under the faucets device to stop stress on the bathtub.
Fit the flexible tap connectors to the bottom of the two faucets using 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut supplied by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Ensure you make use of all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its last position.

Removing Old Taps

If you need to change old taps with new ones as a part of your setup, then the first thing you ought to do is disconnect the water system. After doing so, switch on the taps to drain any kind of water remaining in the system. The procedure of getting rid of the existing faucets can be quite troublesome as a result of the limited accessibility that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the taps. Have a cloth ready for the remaining water that will certainly originate from the pipelines. When the supply pipes have been removed, make use of the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary taps from turning during this process. When the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned of any old securing substance.
Prior to proceeding to fit the brand-new taps, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.

Setting up the Tub

Making use of both wood boards under its feet, place the tub in the needed setting. The wooden boards are useful in equally spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small points.
The next goal is to make sure that the tub is leveled all round. This can be achieved by checking the spirit level and adjusting the feet on the bathtub until the level checks out degree.
To mount faucets, fit all-time low of the furthest flexible tap port to the ideal supply pipeline by making a compression join; after that do the exact same for the various other tap.
Switch on the supply of water and also examine all joints as well as brand-new pipework for leakages as well as tighten them if needed. Fill up the bathtub and additionally inspect the overflow outlet and the normal outlet for leakages.
Lastly, repair the bath paneling as explained in the producer's user's manual. Tiling and sealing around the bathtub should wait till the bath tub has actually been made use of at the very least when as this will certainly resolve it into its last setting.

Fitting New Touches

If the tails of the brand-new faucets are plastic, after that you will require a plastic connector to stop damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end gives a link to the existent supply pipelines.
If you need to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the installing hole in the bath/basin ensuring that the washing machines are in area in between the faucet as well as the sink. Protect the faucet in position with the maker provided backnut. Once the faucet is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former kind should be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.

Tiling Around the Bathtub

In the area where the bath fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to break an inflexible seal, triggering the water to pass through the wall between the bath and also the tiling, leading to problems with wetness and possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, as well as are capable of securing spaces as much as a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water before securing, to permit the activity experienced when the bathtub is in use. The sealant can break rather early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof glue and grout.

How to Install or Replace a Bathtub

Find Your Dimensions

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

 

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

Disconnect the Water Supply and Drain Assembly

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

 

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

 

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

Cut Out the Old Tub

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

 

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

 

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

Install the New Tub

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

 

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

 

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

 

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

Secure the Tub

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

 

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

 

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

 

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

Hopefully you enjoyed reading our section on A Step-by-Step Guide to Installing a Bathtub. Thanks so much for finding the time to browse our short article. Sharing is nice. Helping others is fun. Bless you for your time. Kindly come by our website back soon.

Issue resolved, dial!